Bench 1, sheet v5

One bench, out of a scrap pile. Three 8 ft studs, one 8 ft 1x4, a 3/4 ply offcut. Screws only, no bought hardware. Longest part is 40 in. Never built. v5 cuts the end rail 1/16 short at each end so it goes in by hand, instead of a taper fit that only a perfect splay would let you assemble.

Length
40 in
Seat depth
16-1/2 in
Seat height
17 in
Back top
30-1/2 in
Leg splay
8°
Back angle
105°

The drawing

Side and front elevation, to scale, with dimensions

What changed in v5

The end rail was a taper fit. Now it is a cut with a gap in it. v4 cut the rail to the exact clear space between the leg faces: 8-1/2 at its bottom edge, 7-1/2 at its top. That is a wedge and it has to be perfect. Between two legs bevelled by hand, one degree of splay error and the rail will not go in, and the sheet's answer was "recut the ends", which does nothing when the rail is the right part and the space is too small. The rail is now cut 8-3/8 square, and the ends are marked 1/2 in in from the end of the top face and cut down to the bottom corner. Top edge 7-3/8. That leaves about 1/16 clear at each end, and the 5 in screws draw it in. The cut works anywhere from 7-1/8 to 9-1/8 of leg splay, so a foot bevelled by hand cannot make it bind.

The angle became a mark. 8° on a rail end is a gauge reading, and a gauge drifts a degree over 3-1/2 in. 1/2 in in from the end on the flat top face is a measurement with a square and a rule. Same joint, one less way to be wrong.

Nothing else moved. The legs, seat, back and screw count are v4's. The cut plan gains 1/8 in of offcut.

What v4 fixed

The seat height did not add up. v3 cut the legs 15-1/2 and sat a 3/4 ply top on them: that is 16-1/4, and the sheet kept saying 17. Every number downstream (back top, slat heights) rode on the wrong figure. Legs are now 16-7/16 on the axis, which gives 16-1/4 vertical, and the seat reads 17.

The end rail stopped being a fitted length. v3 said 13-1/2 nominal, fit at assembly to about 12-1/2. A fitted length on a cut list is a hole in a cut list. v4 made it a number, 8-1/2; v5 moves that number 1/8 so it cannot bind.

The post notch is gone. v3 had a 1-1/2 x 3-1/2 notch in the post's lower end, saddling the rear leg. A 1-1/2 x 3-1/2 notch in a 1-1/2 x 3-1/2 post is not a notch, it is the whole end. The post now sits on the seat and is screwed down into the rear apron.

Smaller corrections: the base is 19-1/16 outside to outside, not 21. The slats are 40, flush with the bench ends, not 37. The legs are 3-1/2 deep and 1-1/2 wide along the bench; v3's side view drew them 1-1/2 deep, which contradicted the end rail and the screw length.

Parts

PartStockCutQty
Leg2x416-7/16 on the axis. Both ends cut 8° off square, the two cuts parallel. Cut as mirrored front/rear pairs.4
Long apron2x4 on edge37, between the legs, top flush with the leg tops at 16-1/42
End rail2x4 on edge8-3/8, cut square, then mark 1/2 in in from each end on the top face and cut down to the bottom corner. Top edge 7-3/8, bottom edge 8-3/8. Goes in about 1/16 clear at each end.2
Back post2x414. Top end 15° off square so it sits level at 30-1/2; bottom end 15° off square so it lies flat on the seat.2
Back cleat2x414, top end cut 15° flush with the post top. 1-1/2 thick against the post, 3-1/2 wide out to the slat.2
Corner block2x43-1/2 long, used flat (1-1/2 thick, 3-1/2 x 3-1/2 face). One in each inside corner.4
Back slat1x440 x 3-1/2, ends flush with the bench ends2
Seat top3/4 ply40 x 16-1/2, front edge eased1

Cut plan off three 8 ft studs (92-5/8 each)

StudCutsUsedWith kerfsOffcut
A37 + 37 aprons7474-1/818-5/8
B16-7/16 x 4 legs65-3/466-1/826-7/8
C14 x 4 posts and cleats, then 8-3/8 x 2 end rails72-3/473-3/819-1/4

Kerf counted at 1/8 per cut, so the numbers above already carry it. Corner blocks are 3-1/2 x 4 = 14 in off the end of stud A or C's offcut. Slats: two 40s off the 8 ft 1x4, 16 left over. All 2x4 parts including the blocks come to 226-3/8 against 277-7/8 of stock: 51-1/2 in spare, which is the margin for one leg cut wrong.

Joints

  1. Apron to leg, corner block. Block lies flat in the inside corner: 3-1/2 x 3-1/2 face against the leg, 1-1/2 thick. Two 2-1/2 screws through the block into the leg (1 in of bite in the leg's 1-1/2). Two 2-1/2 through the apron's face into the block (1 in of bite). All four heads are inside the frame.
  2. End rail to legs. The rail drops between the legs, top flush at 16-1/4, and stands about 1/16 clear of each leg face because it is cut 8-3/8 into an 8-1/2 space. Two 5 in screws per end, driven through the leg's 3-1/2 depth into the rail's end: 1-7/16 of bite before the gap closes, 1-1/2 after. Pilot 1/8. Tighten both screws at one end before starting the other, or the rail cocks and jams on one side. Heads on the leg's front and back face, plug or leave. This is the one place the sheet uses end grain. It holds the rail in place, not the seat.
  3. Post to seat. The post's bottom end is cut 15° off square, so it lies flat on the seat at the rear corner, flush with the seat's rear edge. Two 3 in screws per post driven at 45° down and forward through the post's front face: they cross the 3/4 ply and land in the rear apron (or the rear leg, where the post sits over it). Pilot 1/8, countersink, plug. Without a pilot the post's foot will split.
  4. Cleat to post. Four 3 in screws per cleat, driven through the cleat's 1-1/2 thickness into the post's 1-1/2 depth, heads on the cleat's outboard face where the slats will cover them. Keep them 2 in clear of the slat screw lines.
  5. Slat to cleat. Two 1-5/8 per crossing, through the slat's 3/4 into the cleat's 1-1/2. Pilot 1/8, 3/8 in from the slat's edge.
  6. Seat to frame. Eight 1-5/8 screws down into the aprons and end rails, countersunk. No glue. The top is the first part to be replaced.

Screws: 4 x 5 in, 8 x 3 in, 16 x 2-1/2, 16 x 1-5/8. That is 44 screws and nothing else.

Slat heights, above the seat surface

Bottom slat 3-1/2 to 7. Top slat 10 to 13-1/2, its top edge flush with the post tops at 30-1/2. Gap 3 in. This is a lumbar rail and a top rail, not a full back; a third slat is not in the scrap count.

Assembly

  1. Cut the legs first. Mark F and R and the outboard face before the bevel. Bevel both ends 8° and check the two cuts are parallel by standing the leg on a flat surface and looking at the gap under the top face. Drill a small hole through a offcut at 8° and use it as a gauge.
  2. Cut the end rails first, before the frame: 8-3/8 square, mark 1/2 in in from each end on the top face, cut from that mark down to the bottom corner. Top edge 7-3/8.
  3. Lay out each end frame at the top, not at the floor. Set the seat upside down, drop the two legs on it with a 1 in overhang at the front and back edges: that puts the leg outer faces 1 in in from the seat edge and the inner faces 7-1/2 apart. The feet then land 19-1/16 outside to outside. Measure the feet to check the splay; do not lay out from them. Rail between the legs, top flush with the leg tops, ends pulled shut by the screws. Check the two diagonals, not by eye.
  4. Stand up. Long aprons between the legs, top flush at 16-1/4. Outside to outside 40 at the seat line. Corner blocks last in each corner, two screws each way.
  5. Seat on. Eight screws down. Stand it on a flat floor and scribe the four feet; take the difference off the feet until the seat reads 17 at every corner. Never shim.
  6. Back posts on last. Bottom face flat on the seat, flush with the rear edge, two screws at 45°. Then the cleats. Sit on it before the slats go on.
  7. Slats by height, not by even gaps: 3-1/2 and 10 above the seat. Check the top slat's top edge is flush with the post tops before the screws go in.

Checks a builder can actually make

CheckShould readIf it doesn't
One cut leg standing on the floor, floor to top face16-1/4 (16.25)The 8° bevel gauge is off, not the cut length
Seat height at all four corners17, all four within 1/16Scribe the feet and take it off the feet. No shims.
End rail top edge / bottom edge7-3/8 / 8-3/8The 1/2 in marks are off; recut the ends, not the legs
Clear space between the leg faces at the rail's bottom edge8-1/2; 8-3/8 is the floorLegs are too close. The rail is right. Reset the splay, do not cut the rail
Diagonals, each end frameequal within 1/8The frame is racked; loosen the rail screws and re-square
Top slat's top edge vs post topsflush at 30-1/2Slat heights are off; move the slat, don't cut the post
Outside to outside at the seat line40; at the floor 19-1/16Leg splay is off

What I don't know

Nothing here has been cut in wood. I drew it, checked it against itself, and a builder on a forum read v3 and went straight at the end rail: "the fitted end rails are rough on a cut list." He was right, and looking at that line is how I found the 3/4 hole in the height. v5 is the second pass at his line: v4 gave the rail a number, v5 made that number one that a hand-cut frame cannot make fail.

Soft spots I would watch, in order: the bite in the rail's end grain (1-1/2 in with a 5 in screw, pilot 1/8); the 45° post screws, which need a pilot and a steady hand; the 8° bevels on the legs, which is the one operation where a hand saw and a gauge will drift; and the rail's 1/2 in marks, which are easy to mark on the wrong face.

If a line here doesn't add up, name it and I'll change the sheet, not the story.

v4 drawn 2026-11-13, v5 2026-11-15. All dimensions in inches. Every dimension line on the drawing is generated from the same geometry the tables come from, so a label cannot disagree with the shape it measures.